PT-100 MPPT Charge Controller

Maximize Energy Harvest and Improve Battery Life

The PT-100 is a Maximum Power Point Tracker (MPPT) charge controller designed to harvest the maximum available energy from the PV array and deliver it to the batteries.

The PT-100’s MPPT algorithm finds the maximum power point of the array and operates at this point while regulating the output current and battery voltage to fully charge the battery.

Download Owner's Manual (3.01 MB) Download Spec Sheet (104.34 KB) Download Current Firmware (17.66 MB)
Features Includes
  • MPPT
    Maximum Power Point Tracking technology for increased PV power output efficiency.
  • Multi-state Charging:
    Maximizes system performance and improves battery life.
  • Optimal Battery Charging:
    Maximizes system performance and improves battery life.
  • Voltage Options:
    Compatible with 12, 24, or 48V battery systems with automatic detection of system voltage.
  • GFDI:
    Integrated PV Ground- Fault Detection and Interruption/ Indication, with pre-fault leakage/ diagnostic metering.
  • Extensive Electronic Protection:
    Over-temperature protection, power derating when temperature is high, PV short circuit and high PV input shutdown, output overcurrent protection and night-time back-feed (reverse current) protection.
  • Support a Large PV Array:
    A single controller supports a large PV array up to 6600W.
  • High Efficiency:
    The PT-100 provides higher than 99% conversion efficiency and uses less than two watts of power in nighttime mode.
  • LED Indicators and Screen
  • AFCI: An integrated PV Arc-Fault Circuit Interrupter detects, indicates, and extinguishes series arcs. The AFCI is designed to meet the new National Electric Code (NEC) Article 690.11 requirements.
  • Convenient Installation: Run all of the wiring to the unique, remain-inplace wiring box with ease prior to installing the full PT-100 unit.
  • On-site Updates: The PT-100’s software can be updated on site.
  • Easy MP and MMP integration: The PT-100 is designed to work with a Magnum Panel (MP) or Mini- Magnum Panel (MMP). It provides room and access to PV and battery disconnect breakers.

PT-20-10 Solar Charge Controller

Advanced MPPT Support for Smaller PV Systems

The Magnum Energy PT-20-10 Charge Controller by Sensata Technologies is an MPPT controller designed to work with all established module technologies and is optimized for grid-tied PV systems with module voltages higher than the battery voltage. The advanced MPP-tracking algorithm ensures maximum available power produced by the solar panels charges the batteries in any weather.

Download Spec Sheet (89.38 KB)
Features Includes
  • Maximum Power Point Tracker (MPP tracker)
  • Voltage and current regulation
  • Automatic load reconnection
  • Temperature compensation
  • Positive earthing of one or negative earthing of several terminals possible
  • Monthly equalization charge
  • Integrated light controller
  • Overcharge protection
  • Deep discharge protection
  • Reverse polarity protection of module, load and battery
  • Reverse polarity protection by internal fuse
  • Automatic electronic fuse
  • Short circuit protection
  • Overvoltage protection at module input
  • Open circuit protection without battery
  • Reverse current protection at night
  • Overtemperature and overload protection
  • Load disconnection on battery overvoltage

CC Solar Charge Controller

Optimize Battery Maintenance and Monitoring via a Large LCD Display

The Magnum Energy CC Series Charge Controllers by Sensata Technologies provide exceptional control and state-of-charge determination via an easy-to-read LCD display. The large display shows operating modes with the aid of symbols, and the state of charge is represented visually in the form of a level meter. Voltage, current, and an energy meter can also be displayed.

USB ChargingThe CC-40 also features an integrated USB charging port for charging smartphones and tablets.

Download Spec Sheet (156.91 KB)
Features Includes
  • USB Charger
    USB charge outlet for smartphones and tablets
  • Shunt topology with MOSFETs
  • Accurate state of charge (SOC) determination
  • Automatic detection of voltage
  • PWM control
  • Multistage charging technology
  • Load disconnection depending on SOC
  • Automatic load reconnection
  • Temperature compensation
  • Option to use negative earthing of one or positive earthing of several terminals
  • Integrated data logger (energy meter)
  • Evening, night light and daylight functions
  • Integrated self test
  • Monthly equalization charge
  • USB charge socket for smartphones and tablets (CC-40 only)
  • Overcharge protection
  • Deep discharge protection
  • Reverse polarity protection of module, load and battery
  • Automatic electronic fuse
  • Short circuit protection of load and module
  • Overvoltage protection at module input
  • Open circuit protection without battery
  • Reverse current protection at night
  • Overtemperature and overload protection
  • Load disconnection on battery overvoltage

CE Solar Charge Controller

Cost-effective, Essential LED Charge Controller

The Magnum Energy CE Series Charge Controllers by Sensata Technologies are an excellent, cost-effective choice for when simple controls and low self consumption are in order for your charge controller. Available in 6, 10, 20, 30, and 40 amp models, the pulse width modulated (PWM) CE Series automatically recognizes 12V or 24V systems and adjusts accordingly.

USB Charger available on the CE-40.

Download Spec Sheet (142.89 KB)
Features Includes
  • Multi-function Display
    Multifunction, multicolor LED display shows operating states for operation, state of charge, fault messages.
  • Serial topology with MOSFETs
  • Automatic detection of voltage
  • Voltage regulation
  • PWM control
  • Multistage charging technology
  • Current compensated load disconnection
  • Automatic load reconnection
  • Temperature compensation
  • Negative earthing of one or positive earthing of several terminals possible
  • Monthly equalization charge
  • Overcharge protection
  • Deep discharge protection
  • Reverse polarity protection of module (≤36 V), load and battery
  • Automatic electronic fuse
  • Short circuit protection of load and module
  • Overvoltage protection at module input
  • Open circuit protection without battery
  • Reverse current protection at night
  • Overtemperature and overload protection
  • Load disconnection on battery overvoltage

ACLD-40 AC Load Diversion Controller

The Most Sophisticated Way to Add Three-Stage Charging to your AC-Coupled System

What is an ACLD – AC Load Diversion Controller?
The ACLD monitors the battery voltage of a backup battery bank, and if the voltage rises to a predetermined level, the ACLD connects a diversion load of sufficient size, to the battery or energy source to prevent the battery voltage from increasing any further. The controller will continue to engage and disengage the load as often as necessary to prevent battery overcharge.

An AC Load Diversion controller is used to divert excess energy to an AC load in an effort to keep the battery bank that is connected to a back-up inverter from being overcharged, when used in an AC Coupled application.

 
Download Owner's Manual (1.95 MB) Download Spec Sheet (208.42 KB)
Features Includes
  • Robust
    Controls up to 4000 watts of excess power to prevent battery over-charge.1
  • Multiple VDC Systems
    Works with 12, 24, or 48 volt systems.
  • Flexible
    Allows the use of common, resistive AC household loads instead of hard-to-find DC loads to divert excessive current.
  • Communication
    Easy access Inverter and Network ports.
  • Network
    Standard RS485 MagNet protocol to communicate with Magnum inverters and remotes.
  • All Sources
    Can utilize power generated from wind, solar, or hydro systems.
  • Output
    Provides PWM (Pulse Width Modulation) voltage when powering diversion load to run load without flicker.
  • Works with MS-PAE, MS-PE, MMP Panel, and MP Panel Systems